Matek H743-SLIM

Multirotors → FPV Racing drones → Flight controllers → H7 FCs → Matek H743-SLIM

in the store

FREE SHIPPING
Stock level: 10

Recommended stores

Banggood FREE SHIPPING Out of stock	$80

↓ Another stores

MCU:	H743
Gyro:	ICM20602 & MPU6000
Barometer:	DPS310
OSD:	+
CAM in:	2
Power :	2-8S
3.3V BEC:	0.2A
5V BEC:	2A
Current Sensor:	-
PWM:	13
ESC type:	-
ESC:	-
BLHeli:	-
Receiver:	-
RSSI:	+
VTX:	-
UART Rx:	7
UART Tx:	7
I²C:	2
CAN:	1
Buzzer pad:	+
LED pad:	+
Vbat:	2
CURR pad:	2
Air speed:	+
IR/INR pad:	+
Blackbox:	MicroSD
USB:	Type-C
USB pads:	+
DJI compatible:	+
Bluetooth:	-
Size:	36x36x5mm
Mount Holes:	30.5x30.5mm
Weight:	7g

Flight Controller H743-SLIM

STM32H743VI, ICM20602 & MPU6000, DPS310, OSD, 7x UARTs, 2x I2C, 1xCAN, 13x PWM outputs, BEC5V,

Firmwares

Gallery

Specifications

FC Specifications

MCU: STM32H743VIH6, 480MHz , 1MB RAM, 2MB Flash
IMU: MPU6000 (SPI1) & ICM20602 (SPI4)
Baro: Infineon DPS310 (I2C2)
OSD: AT7456E (SPI2)
Blackbox: MicroSD card socket (SDIO)

7x Uarts (1,2,3,4,6,7,8) with built-in inversion.
13x PWM outputs(including “LED” pad)
2x I2C
1x CAN
6x ADC (VBAT, Current, RSSI, Analog AirSpeed, Vbat2, Cur2)
3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
1x SPI3 breakout
USB Type-C(USB2.0)
1x JST-SH1.0_8pin connector (Vbat/G/Curr/Rx8/S1/S2/S3/S4)
1x JST-GH1.25_4pin connector (5V/CAN-H/CAN-L/G)

Dual Camera Inputs switch
5V/Vbat filtered power ON/OFF switch

DJI FPV OSD is supported by any spare UART

Power

Vbat Input: 6~36V (2~8S LiPo)
BEC: 5V 2A cont. (Max.3A)
LDO 3.3V: Max.200mA
No Current Sensor built-in
ADC Vbat2 pad supports Max. 69V (voltage divider: 1K:20K)
Static power: 200mA@5V with Betaflight, 150mA@5V with ArduPilot

FC Firmware

ArduPilot(ChiBiOS): MATEKH743
BetaFlight: MATEKH743
INAV: MATEKH743 (To be supported soon)

Physical

Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm
Dimensions: 36 x 36 x 5 mm
Weight: 7g

Including

1x H743-SLIM
6x Silicon grommets M4 to M3
1x JST-SH1.0_8pin cable, 5cm
2x JST-SH1.0_8pin connectors
1x JST-GH-4P to JST-GH-4P cable for CAN port, 20cm

Layout

Wiring

ArduPilot mapping

PWM PWM1~PWM13 are Dshot and PWM capable. However, mixing Dshot and normal PWM operation for outputs is restricted into groups, ie. enabling Dshot for an output in a group requires that ALL outputs in that group be configured and used as Dshot, rather than PWM outputs. If servo and motor are mixed in same group, make sure this group run lowest PWM frequency according to the servo specification. ie. Servo supports Max. 50Hz, ESC must run at 50Hz in this group.	S1	PB0	5 V tolerant I/O	PWM1 GPIO50	TIM8_CH2N	Group1
	S2	PB1	3.3 V tolerant I/O	PWM2 GPIO51	TIM8_CH3N	Group1
	S3	PA0	5 V tolerant I/O	PWM3 GPIO52	TIM5_CH1	Group2
	S4	PA1	5 V tolerant I/O	PWM4 GPIO53	TIM5_CH2
	S5	PA2	5 V tolerant I/O	PWM5 GPIO54	TIM5_CH3
	S6	PA3	5 V tolerant I/O	PWM6 GPIO55	TIM5_CH4
	S7	PD12	5 V tolerant I/O	PWM7 GPIO56	TIM4_CH1	Gourp3
	S8	PD13	5 V tolerant I/O	PWM8 GPIO57	TIM4_CH2
	S9	PD14	5 V tolerant I/O	PWM9 GPIO58	TIM4_CH3
	S10	PD15	5 V tolerant I/O	PWM10 GPIO59	TIM4_CH4
	S11	PE5	5 V tolerant I/O	PWM11 GPIO60	TIM15_CH1	Group4
	S12	PE6	5 V tolerant I/O	PWM12 GPIO61	TIM15_CH2	Group4
	LED	PA8	5 V tolerant I/O	PWM13 GPIO62	TIM1_CH1	Group5
	LED	PA8	5 V tolerant I/O	SERVO13_FUNCTION 120, NTF_LED_TYPES neopixel		Group5

ADC	No pad 1K:10K divider builtin	PC0	0~36V	on board battery voltage	BATT_VOLT_PIN BATT_VOLT_MULT	10 11.0
	No pad	PC1	0~3.3V	on board current sensor	BATT_CURR_PIN BATT_AMP_PERVLT	11 40
	Vbat2 Pad 1K:20K divider builtin	PA4	0~69V	Vbat2 ADC	BATT2_VOLT_PIN BATT2_VOLT_MULT	18 21.0
	Cur2 Pad	PA7	0~3.3V	Cur2 ADC	BATT2_CURR_PIN BATT2_AMP_PERVLT	7 /
	RSSI Pad	PC5	0~3.3V	RSSI ADC Analog RSSI	RSSI_ANA_PIN RSSI_TYPE	8 1
	AirS Pad 10K:10K divider builtin	PC4	0~6.6V	AirS ADC Analog Airspeed	ARSPD_PIN ARSPD_TYPE	4 2

I2C	I2C1 CL1/DA1	PB6/PB7	5 V tolerant I/O	Digital Airspeed I2C	ARSPD_BUS	1
				MS4525 MS5525 DLVR-L10D	ARSPD_TYPE	1 3 9
				Compass	COMPASS_AUTODEC	1
	I2C2 CL2/DA2	PB10/PB11	5 V tolerant I/O	on board Baro DPS310

CAN	CAN1	PD0/PD1	5 V tolerant I/O	F103/F303 CAN Node	CAN_D1_PROTOCOL CAN_P1_DRIVER	1 1
				CAN GPS	GPS_TYPE	9
				CAN Compass	COMPASS_TYPEMASK	0
				CAN Airspeed sensor	ARSPD_TYPE	8

UART	USB	PA11/PA12	5 V tolerant I/O	USB	console	SERIAL0
	RX7 TX7 RTS7 CTS7	PE7/8/9/10	3.3 V tolerant I/O	UART7	telem1	SERIAL1
	TX1 RX1	PA9/PA10	5 V tolerant I/O	USART1	telem2	SERIAL2
	TX2 RX2	PD5/PD6	5 V tolerant I/O	USART2	GPS1	SERIAL3
	TX3 RX3	PD8/PD9	5 V tolerant I/O	USART3	GPS2	SERIAL4
	TX8 RX8	PE1/PE0	5 V tolerant I/O	UART8	USER	SERIAL5
	TX4 RX4	PB9/PB8	5 V tolerant I/O	UART4	USER	SERIAL6
	TX6 RX6	PC6/PC7	5 V tolerant I/O	USART6	RC input/Receiver	SERIAL7
				RX6	SBUS/IBUS/DSM
				RX6	PPM

ArduPilot Relay

Camera-1 and Vsw On by default
Make sure 2 cameras are set with identical video format, both PAL or both NTSC.

# GPIOs

PD10 PINIO1 OUTPUT GPIO(81) //Vsw pad power switch
PD11 PINIO2 OUTPUT GPIO(82) //Camera switch

# RCx_OPTION: RC input option

28 Relay On/Off
34 Relay2 On/Off
35 Relay3 On/Off
36 Relay4 On/Off

e.g.

RELAY_PIN 81 //Vsw GPIO
RC7_OPTION 28 //Relay On/Off, Use CH7 of Transmitter to switch Vsw
RELAY_PIN2 82 //Camera switch GPIO
RC8_OPTION 34 //Relay2 On/Off, Use CH8 of Transmitter to switch camera

RELAY_PIN3 81 //Vsw GPIO
RC9_OPTION 35 //Relay3 On/Off, Use CH9 of Transmitter to switch Vsw
RELAY_PIN4 82 //Camera switch GPIO
RC10_OPTION 36 //Relay4 On/Off, Use CH10 of Transmitter to switch camera

The configured feature will be triggered when the auxiliary switch’s pwm value becomes higher than 1800. It will be deactivated when the value falls below 1200.

Check the pwm value sent from the transmitter when the switch is high and low using the Mission Planner’s Initial Setup >> Mandatory Hardware >> Radio Calibration screen. If it does not climb higher than 1800 or lower than 1200, it is best to adjust the servo end points in the transmitter.

reserved

Tips

ArduPilot Firmware
- https://firmware.ardupilot.org/Plane/stable/MatekH743/
- https://firmware.ardupilot.org/Copter/stable/MatekH743/
INAV is expected to support H743 in 2.6.
H743-SLIM has betaflight firmware preloaded for QC
BetaFlight target is not on the Github, pls download BetaFlight firmware from our website.
If you flash ArduPilot firmware via BetaFlight configurator. there is a known issue that flash process will freeze at 50% if “full chip erase” is selected. Disable full chip erase when flashing, then reset to default in Mission Planner after flashing.
It is highly recommended to use STM32CubeProgrammer to erase MCU and upload firmware http://www.mateksys.com/?p=6905

Resellers

Prices for Matek H743-SLIM in stores

Deals found: 32 (AliExpress³, Banggood¹)

Store	Stock level	Lot price	Shipping cost	Coupon / promocode	Pcs./lot	1pc price
Banggood	Out of stock	$80			1	$80
AliExpress	Stock level: 10	$85			1	$85
AliExpress	High stock level	$90			1	$90
AliExpress	High stock level	$85	+ $5.74		1	$91

Flight controllers

Matek H743-SLIM

Flight Controller H743-SLIM

Prices for Matek H743-SLIM in stores

See also